Trade Name: Astro Thermal Fire PS
Thermal Fire Pipe Sleeve
Suitable for fire protecting a wide range of plastic and metal pipes.
Tested to BS476: Part 20
Tested to BS EN 1366-3
Up to 2 Hours Fire Rating
Acoustic Tested to BSEN ISO 140-3
Maintains thermal insulation for the pipe
For use through a wide range of fire partition walls and floors.
Allows for thermal movement of pipe
No additional metal sleeving or lining out of the partition aperture required
Cost effective, can be cut to length
A high percentage of the steel, copper and plastic pipes found in commercial and domestic buildings will penetrate through fire rated constructions such as ceilings, floors and walls. Once a hole is made in a fire rated construction for the passage of pipes or services the integrity of the compartment is compromised.
To solve this problem Astroflame have developed ASTRO Thermal Fire Pipe Sleeve, which reinstates the fire rating of the construction and prevents fire spreading from one compartment to another. It also protects copper pipes from cement erosion.
The sleeve is a cost effective product for the fire stopping of pipe penetrations, e.g. plumbing pipe and metallic pipes, whilst maintaining similar thermal and acoustic properties as standard mineral fibre insulation. These properties ensure compliance to water bye laws and building regulations for cold and hot water pipes and heating systems.
In a fire situation the sleeve expands to fill the available space between the pipe and the penetration. In the case of plastic pipes the sleeve will crush and close off the pipe forming a solid char and preventing the passage of fire and smoke to the adjacent compartment.
Tested in Plasterboard Partition, Mineral Fibre Batt, Solid Walls and Floors.
Tested on the following pipe sizes to BS 476 Part 20 and BS EN 1366-3 for up to 2 hours.
All sleeves have been tested with a 25mm nominal wall thickness. Sleeves have been tested cut flush to the wall for metal pipes only and floor for metal and plastic pipes. Sleeves have also been tested in walls, for plastic pipes, leaving 25mm exposed for connection to standard pipe insulation.
The sleeve is simple to install, easy to cut and one sleeve can replace two collars. For metal pipes the sleeve may also be fitted flush to the wall for a clean line solution.
Thermal Pipe Sleeve Length 300mm. Wall thickness 27mm.
To Order & Specify
Please contact us and quote the following information - Please quote- Quantity / Trade name / Product Ref / Size
Fire Test and Assessment Reports
BS476 part 20/22 2 hour rated at Chiltern International Fire 132 minutes integrity and insulation
For further information on installation requirements please review the 2 installation videos (On a plaster Wall and Solid wall) or the Technical Data Sheet or contact the technical team on: tel 01329 844 500 or email firstname.lastname@example.org
Health and Safety
The product does not present any known health hazards during or after installation. Normal good industrial and personal hygiene practices should be observed. For further information on health and safety requirements please contact the technical team on: tel 01329 844 500 or email email@example.com
As part of our policy of ongoing improvements, we reserve the right to modify, alter or change product specifications without giving notice. Product illustrations are representations only. All information contained in this document is provided for guidance only, and as ASTROFLAME (FIRE SEALS) LTD has no control over the specific application or installation methods of the products, or of the prevailing site conditions, no warranties expressed or implied are intended to be given as to the actual performance of the products mentioned or referred to, and no liability whatsoever will be accepted for any loss, damage or injury arising from the use of the information given of products mentioned or referred to herein.
The above information to the best of our knowledge is true and accurate and based upon current test data and is supplied for your guidance only. Customers should satisfy themselves to the suitability of the product based on the products limitation of applications and that the product is fit for purpose for their intended use and no guarantee is given or implied since the conditions of actual use are beyond our control. ASTROFLAME (FIRE SEALS) LTD, disclaim any liability for loss, damage or other expense arising from the use of information, data or products mentioned or referred to and reserve the right to change any details or specifications without notice. If you are in any doubt as to the suitability of this product for your intended application please contact our technical team on 01329 844500 or email firstname.lastname@example.org and we will contact you.